Hot-dip galvanizing, a tried and tested technology which provides barrier protection and cathodic corrosion protection, ensures safety and structural integrity when applied to fasteners. Although South Africa has the capability and capacity to manufacture these, volumes remain small. A clearer understanding of the benefits of hot-dip galvanizing fasteners – as well as the knowledge of and adherence to stringent industry standards – could grow the market and benefit the entire supply chain, says Robin Clarke, Executive Director of the Hot Dip Galvanizers Association of Southern Africa (HDGASA).
The nuts and bolts of hot-dip galvanising
The conventional method of hot-dip galvanizing, jigging components onto a flight bar and dipping them into molten zinc, is not feasible for small fasteners. Instead, they are placed in perforated baskets for hot-dip galvanizing, and then transferred to a centrifuge to spin off any unreacted zinc. This leaves a carefully controlled amount of zinc on the fastener with very good definition in the threaded area.
For the hot-dip galvanizing of fasteners, the HDGASA supports and promotes adherence to the ISO 10684 and the SANS 121:2024 / ISO 1461:2022 standard. These specify a minimum coating thickness of 50 microns for threaded articles with a diameter exceeding 6mm; and 25 microns for those with diameters equal to or less than 6mm.
Clarke emphasises that engineers design structures with sufficient strength to perform their functions: “Corrosion control is integral to strength calculations. The use of the correct fasteners, particularly in a structural steel environment or highly corrosive climate, is critical. The considerations applied to corrosion control of nuts and bolts should, at all times, equal those applied to the main structural members.”
Fastening on to the benefits
A common misconception among users is that any zinc-coated item is hot-dip galvanized: “Hot-dip galvanizing produces a significantly thicker zinc coating than zinc plating. Often fasteners specified as hot-dip galvanized are supplied as zinc-plated, resulting in reduced durability due to thinner coatings,” Clarke observes.
A zinc-plated fastener typically has a coating thickness of around 10 microns, which is 2.5 to 5 times thinner than the minimum specified in hot-dip galvanizing standards. It follows that hot-dip galvanizing offers a 2.5 to 5 times greater level of corrosion control and service life.
Clarke also warns against using stainless steel fasteners to connect hot-dip galvanized steel components: “This mismatch of materials creates a galvanic corrosion cell which accelerates corrosion of the hot-dip galvanized component. In fact the hot-dip galvanized component sacrifices itself to protect the stainless-steel nuts and bolts. The hot-dip galvanized steel retreats from the stainless steel, giving the incorrect impression that the hot-dip galvanized coating has failed.”
Price and aesthetics are also challenges, with the thin coating on a painted article appearing more attractive and more cost-effective. Clarke concedes that, with South African construction supply chains under pressure, there is always a temptation to resort to cheaper options, without sufficiently considering how these will perform from a safety and quality perspective.
Connecting over challenges
Furthermore, Clarke points out that concerns surrounding hot-dip galvanizing of high tensile nuts and bolts which exceed a 1 000 mega Pascals (MPa) tensile strength rating are to be re-evaluated: “While it is perceived that these are prone to hydrogen embrittlement during the galvanizing process and should not be hot-dip galvanized, German companies are hot-dip galvanizing tensile fasteners at volume. This is done by mechanically cleaning fasteners and flash pickling them, to minimise the potential for hydrogen ingress into the fastener,” he explains.
He also mentions that correct storage and handling of hot-dip galvanized fasteners is imperative. These should be stored and delivered to site with the nut secured onto the bolt:
“The torqueing of hot-dip galvanized fasteners is usually done by the ‘turn of the nut’ method. The method of fastening is to turn the nuts to achieve a snug fit between plies. Once that is done, the nut is marked and then turned (depending on the size and length of the nut and the bolt) by a further third to two-thirds full turn.
Correctly hot-dip galvanized fasteners play an integral role in the ‘nuts and bolts’ of durable, successful steel construction: “The HDGASA is committed to working with our members and the wider steel supply chain, to ensure the quality and standards of hot-dip galvanized fasteners, through the provision of guidance, technical education and advisory services,” Clarke concludes.
Gunhawk
Dr. Judy Dlamini is a qualified medical doctor, with an MBA and PhD in business leadership. She is an accomplished businesswoman, an author, and founder and current executive chairperson of the Mbekani Group. After a successful medical career spanning 10 years, Dlamini decided to explore new terrains, she enrolled for an MBA degree, after which she joined HSBC Investment Bank, and pursued her PhD through UNISA. Today, Dlamini owns and operates luxury retail stores; Luminance. The fledgling business, Mbekani Group, she started 20 years ago has grown into a diverse and successful entity with operations and investments in medical devices, health management, facilities management, retail and property. In addition to a long and successful business career, she and her husband are founders and trustees of Mkhiwa trust, a family public benefit organisation with a focus on rural development and education.